I am trying to set up plate solving and apparently need an mage to attached to the config file.
I have tried astro bin but can’t get any numbers I see that to work in the config file. Aand I have no fit files to use.
What do I do now?
I am going to try and attach my log file here. Lets see if I can do this…
Can someone translate the plate solving errors??
[12-24-17 19:37:21.396][DEBUG] [Telescope Thread] *********** SUCCESSFUL SOLVE *************
[12-24-17 19:37:21.396][DEBUG] [Telescope Thread] SOLVER: True
[12-24-17 19:37:21.396][DEBUG] [Telescope Thread] SUCCESS: False
[12-24-17 19:37:21.396][DEBUG] [Telescope Thread] CONF: 0
[12-24-17 19:37:21.396][DEBUG] [Telescope Thread] BLIND: True
[12-24-17 19:37:21.396][DEBUG] [Telescope Thread] RA: 0
[12-24-17 19:37:21.396][DEBUG] [Telescope Thread] DEC: 0
[12-24-17 19:37:21.396][DEBUG] [Telescope Thread] SCALE: 0
[12-24-17 19:37:21.396][DEBUG] [Telescope Thread] FLIPPED: False
[12-24-17 19:37:21.396][DEBUG] [Telescope Thread] ANGLE (EON): -500
[12-24-17 19:37:21.396][DEBUG] [Telescope Thread] MSG: Failed to solve image
[12-24-17 19:37:21.396][DEBUG] [Telescope Thread] ******************************************
[12-24-17 19:37:21.396][DEBUG] [Telescope Thread] Auto center validation frame solve failed. Failed to solve image
[12-24-17 19:37:21.396][DEBUG] [Telescope Thread] Adding sequence level notification: Auto center validation frame solve failed. Failed to solve image
[12-24-17 19:37:32.472][DEBUG] [Main Thread] Centering: User abort…
[12-24-17 19:37:32.588][DEBUG] [Sequence Thread] Something has gone wrong when centering the target, but recovery mode is NOT active!
[12-24-17 19:37:32.588][DEBUG] [Sequence Thread] Adding sequence level notification: Something has gone wrong when centering the target, but recovery mode is NOT active!
[12-24-17 19:37:32.594][DEBUG] [Sequence Thread] Error on auto center, aborting sequence!
[12-24-17 19:37:33.768][DEBUG] [PHD2 Listener Thread] PHD2 - No messages received from PHD2 for 1 minute, checking socket with status…
[12-24-17 19:37:33.768][DEBUG] [PHD2 Listener Thread] Checking PHD2 state…
[12-24-17 19:37:33.768][DEBUG] [PHD2 Listener Thread] PHD2 GetPhdStatus - Pre-Wait : Stopped
[12-24-17 19:37:33.768][DEBUG] [PHD2 Listener Thread] Sending to PHD2:
{“method”: “get_app_state”, “id”: 1001}
[12-24-17 19:37:33.768][DEBUG] [PHD2 Listener Thread] PHD2 GetPhdStatus - Post-Wait: Stopped
[12-24-17 19:37:34.704][DEBUG] [Sequence Thread] DoEventGroupChange: Error in auto center (True)
[12-24-17 19:37:34.743][DEBUG] [Sequence Thread] DoEventGroupChange: Complete
[12-24-17 19:37:34.746][DEBUG] [Sequence Thread] Cannot start seqeunce. EventGroupChange failed.
[12-24-17 19:37:34.748][DEBUG] [Sequence Thread] ********* Run post sequence *********
[12-24-17 19:37:34.750][DEBUG] [Sequence Thread] SGPro capture cal frame mode is OFF…